1.操作回轉鼓風機時要注意。要避免回轉鼓風機的碰撞和沖擊，不要將回轉鼓風機放在上面并進行操作以防止?jié)櫥?/div>
1. Pay attention to safety when operating the rotary blower. To avoid collision and impact of the rotary blower, do not put the rotary blower on it and operate it to prevent lubrication.
2.回轉式鼓風機機室應有通風口和通風機。通風口應放置在上下兩側，以利于空氣對流，防止機房溫度影響回轉鼓風機的正常運行。
2. The rotary blower room shall be equipped with vents and ventilators. Vents shall be placed on both sides to facilitate air convection and prevent the temperature of the machine room from affecting the normal operation of the rotary blower.
3.盡量在機房內壁周圍放置降噪材料，以減少噪音。
3. Try to place noise reduction materials around the inner wall of the machine room to reduce noise.
4.回轉鼓風機應水平安裝。
4. The rotary blower shall be installed horizontally.
5.配氣管徑不應小于回轉鼓風機的出風口直徑，并注意管內的清潔度。送氣管應安裝在水面以上，以防止管道中的水在啟動時產生過大的壓力。
5. The diameter of the air distribution pipe shall not be less than the diameter of the air outlet of the rotary blower, and pay attention to the cleanliness of the pipe. The air supply pipe shall be installed above the water surface to prevent the water in the pipe from generating excessive pressure during startup.
6.小心不要在接管時敲擊止回閥（止回閥的凸起部分應朝上）。
6. Be careful not to knock the check valve when connecting pipe (the convex part of the check valve should face upward).
7.請正確連接配電線，并注意電機轉向與旋轉鼓風機的旋轉方向一致。
7. Please connect the distribution wire correctly, and note that the rotation direction of the motor is consistent with that of the rotary blower.
8.當使用兩個回轉鼓風機進行交替運行時，應避免在短時間內頻繁更換發動機。一臺回轉式鼓風機的連續運行時間不小于12小時。
8. When two rotary blowers are used for alternate operation, frequent engine replacement in a short time shall be avoided. The continuous operation time of a rotary blower shall not be less than 12 hours.
The above is a detailed introduction to Hunan low-noise rotary fan, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional service http://rohs-international.com/
TEL:400-9901-557
TEL:18678880998
公司地址：山東省濟南市章丘區相公街道大康村村南
濟南道源豐達機械制造有限公司
備案號：魯ICP備2022009540號-1 魯公網安備37018102000745號
